• Author should submit only unpublished paper in IJREI, Please make sure that your paper has not published anywhere else. We will not be liable for any duty of copyright disputes caused by the author. Before submission please make sure that your paper is prepared using IJREI paper template. Acceptance or rejection email will be sent to author within 3-5 working days.
• The manuscript would be considered under all the branches of Engineering &Technology, Management and Applied Science, but not limited.

• Once the paper is accepted, author can pay online any time through online banking, credit card and debit card etc.
• After successful payment, author should submit the final version of paper, copyright form (filled and signed) and payment proof to editor@ijrei.com..

Research Article
The articles should provide aon scientific topics along with experimental and analytical results.The manuscript should be prepared in English using MS word and it should havethe following headings.reviewcomprehensive

Title Page
This page should contain the title of the paper in bold, title case (16, Time New Roman)name of the author should be in title case (italic, 9, Time New roman) with address. Corresponding author has the responsibility to ensure that all the co-authors are aware and approve the content of the submitted manuscript.,

Abstract
An abstract should be summarized in one paragraph with time new roman font size 10, single line spacing, italic, justified and should contain at least 200-250 words. Please do not make references and any type of equationabstract.in

Keywords
Author(s) must give 4-6 key words after abstract. These keywords should be typed at the end of the abstract.appropriate

Introduction
It should be a succinct statement of the background to the work presented, including relevant earlier work, suitablypurposeof the investigation and relating the manuscript to similar previous research.,referenced

Materials and Methods
This section must contain all the important materials, equipment's and manufacturer name (if possible)location to make it simpler for other researchers to reproduce the result. New methods or substantially modified methods may be described in sufficient detail. The statistical method and the level of significance chosen will be clearly stated.withalong

Captions for figures/tables
Caption of figure and table should beof 9 point Times Roman (Bold) (e.g. Figure 1. Figure name). A caption should be inserted in each figure. The legend should be typed in the manuscript directly beneath the figure. Legends are to be listed in numerical order and shouldlabeled as "Figure 1", "Figure 2" and Table 1, Table 2 etc.

Result and Discussion 
In this section elaborate your result and discussion,sizefor this section should be 10, times new roman. Do not under lineany heading or any content. The result and discussion should be presented briefly. The interpreted results should beclearlyexplained in discussions and should relate them to the existing knowledge in the field as much as possible. Tables, Graphs and figures (Illustrations) should be inserted at the end of the manuscript and should have appropriate numbers and titles with an explanatory heading. Color photographs and illustrations (line drawings, halftones, photos, photomicrographs etc) must be clear, sharp and original. Digital files are recommended for highest quality reproduction and should follow the following guidelines.fontthe

• 300dpi or higher sized to fit journal page
• JPEG, GIF, TIFF and PDF formats are preferred)
• Acknowledgement (if any)

Conclusions
A conclusion section must be includedclearlyindicate the advantages, limitations, and possible applicationsof the paper. Although a conclusion may review the main points of the paper, but do not replicate the abstract as the conclusion. A conclusion must elaborate the importance of the work or suggest applications and extensions.shouldand

Acknowledgements

References
References should be written in the following manner
[1] D. Mohanti and P.Hasan, "Analysis of mechanical properties of aluminium alloy, International journal of research in engineering and innovation, vol. 2 issue 4 Dec. 2001, 2127-2130
[2] D. Mohanti and P.Hasan, "Analysis of mechanical properties of aluminium alloy, International journal of research in engineering and innovation, vol. 2 issue 4 Dec. 2001, 2127-2130

Copyright Form
Submission of the manuscript shows that the manuscript has not beenpublishedpreviouslyand is not considered for publication elsewhere. Content of manuscript should be original. Corresponding author is required to sign a CRF form (Copy Right Form) once the manuscript is accepted which would be sent to thecorresponding author's email. The corresponding author can download the form, sign it and can be send as an attachment file through email or by post/courier.